No products in the cart.
PR+MISE Pulse Oximeter FDA SPO2 PI PR Blood Oxygen Digital Monitor
Description
Fingertip Pulse Oximeter use non-invasive infrared technology to measure the pulse oxygen saturation and pulse rate, this type of device can monitor the oxygen supply status of body and prevent the danger of hypoxia. Nowadays, the Pulse Oximeter is widely used in home care, hospitals, health and it is recommended to use before or after sports.
- PI INDICATOR FUNCTION: Perfusion Index.PI as a parameter indicator can reflect the limb perfusion status of the subject.It can be detected under weak or low perfusion to shows the accuracy of machine.
- ACCURATE: Hospitals reflect that our Pulse Oximeter have a good precision as patient monitor
- DISPLAY MODES: 6 display modes of SPO2,Perfusion Index,Pulse Rate,Pulse Wave,Bar Graph.Our Pulse Oximeter is convenient to read in all directions.
- SETTING MENU: Humanized Menu And Prompts, Adjustable Brightness,Alarm function and Memory Of Last Setting Etc.
- BATTERY LIFE: Low power consumption, work over 12 hours. Auto switch-off after 8 seconds if no signal detected.
- EASY OPERATING: One key switching for 6 display interfaces and setting menu.
Package includes:
- 1x PR+MISE Pulse Oximeter
- 1x Lanyard
- 1x Operate Manual
- PRODUCT SIZE: 64mm(L) X 38.8mm(W) X35.5mm(D)
- Approx: 64.5g with batteries
- PACKAGE SIZE: 82mm(L) X69mm(W) X40mm(D)
How to use it:
Step 1
Turn on the pulse oximeter by firmly pressing the power button. The screen should light up almost instantly.
Step 2
Place the sensor — the part that opens and closes like a clothespin — on any finger, with the sensor screen above the fingernail. If the sensor doesn’t have a screen, run the cable along the back of the finger or hand. Don’t use the thumb because readings are less reliable than finger readings.
Step 3
Wait quietly while the pulse oximeter acquires a signal. This may take 10 seconds or more, depending on the device and the conditions. Excessive movement during measurement can decrease the accuracy of the result or may cause an error message.
Step 4
Look at the display to see the heart rate, usually indicated with a heart or pulsing light. The percent of oxygen saturation is typically indicated by the symbol “SpO2.” Many devices also have a pulse tone that beeps in time with the heart rate.
Step 5
Leave the sensor on for continuous monitoring. The sensor can become uncomfortable or cause pressure sores if left on the finger too long. Check and/or move the sensor at least every two to four hours. If only a single measurement is required, remove the sensor and press the power button to turn off the device.
Tips:
To ensure proper function, read the manual for your specific pulse oximeter.
Remove nail polish, especially dark colors, before placing the sensor on the finger.
Place the sensor on the finger before turning on the pulse oximeter for a faster result.
Pulse oximeters are less accurate if there is poor blood flow to the finger. This may occur if the person is cold, has very low blood pressure or is having a heart attack.
Carbon monoxide — due to smoke inhalation, carbon monoxide poisoning or heavy cigarette smoking — results in falsely high pulse oximeter readings.
Altitude may result in lower percent oxygen saturation due to the lower oxygen pressure in the air, particularly if you have recently arrived.
Warning
A normal percent oxygen saturation reading is in the 95 to 100 percent range. In the event of a low oxygen saturation measurement, look for signs of respiratory distress. This includes shortness of breath, wheezing, difficulty breathing or a bluish discoloration of the face, lips or fingernails.
Seek medical attention right away if the respiratory distress is a new or uncomfortable symptom. if it’s getting worse or if the pulse oximeter measurement is below 90 percent.
Additional information
| Brand Name | pr+mise |
|---|---|
| Commodity Quality Certification | FDA |
| Size | PRO-M170 |
| Material | ABS |
| Application | Finger |
| Item Type | Blood Pressure |
| Model Number | PRO-M170 |
| Certificate | FDA |
| Measurement | SPO2,PR,PI |
| Display | OLED display |
| Power Supply | 2 X 1.5V(AAA) Battery |
| Weight | Approx 64.5g |
| Colors | blue,gray,orange,rose red |
Reviews (4)
4 reviews for PR+MISE Pulse Oximeter FDA SPO2 PI PR Blood Oxygen Digital Monitor
Add a review
You must be logged in to post a review.
You may like these products also
$107.95 – $112.95
$35.00 – $42.00
Customer –
Заказ не отправлен и закрыт. При этом пока не вижу, чтобы деньги вернулись
E***a –
Товар не был отправлен. Автоматически возврат средств.
D***v –
Товар не пришел. Деньги вернули.
F***i –
tutto ok