SaTracer 3SW NEW Satcontrol HH Motor Mount DisEqC 1.2 GOTO X Sm3d22

We Sell Wholesale & Retail

Order Online or Call us at 1-888-519-9595 or 1-614-529-9560

1- SATELLITE BUNDLES

2- RECEIVERS

3- DISHES & MOUNTS

4- LNBF

5- SIGNAL METERS

6- HH MOTORS

7- SWITCHES

8- HEADEND / VSAT

9- SUPPLIES

10- AV ACCESSORIES

11- REMOTE CONTROLS

12- OTHER PRODUCTS

Surge Protectors
Security Cameras

Home > HH Motors > SM3D22

Model: SM3D22 aka SaTracer 3 SW
SATCONTROL HH MOTOR

Discontinued - See other motors here

The SaTracer 3 SW is the latest HH motor by Satcontrol. It has an integrated DiSEqC switch to switch between two separate LNBFs. This built-in switch can also be used to switch between a motorized dish and a stationary dish. Metal gearing inside. Works with all DiSEqC 1.2, 1.3, USALS or "Goto X" compliant receivers.

Once the satellite positions have been programmed in the system, the motor returns the dish to exactly the correct location when you switch channels.

The principal of a motorized system is that the dish moves from east to west to track the satellites positioned along the Clarke belt. It utilizes a data stream passed up the LNB co-axial lead to the mount. Only one co-axial cable (the one that goes to the LNBF) is needed for installation.

Since the shaft size is 1 5/8", you will be able to use both Pole-mount and U-bolt type dishes with this motor. The shaft has 2 cross through holes to allow you to mount the dish securely.

Mounts on Pole Size up to 2.5"

Standard Shaft Size: 1 5/8" (42mm) Small shaft diameter to fit most dishes.

Download owner's manual English

Installation Help

Made in Slovenia, Europe

1 YEAR MFG WARRANTEE

Motorized Satellite System Installation Video

Operating protocol	DiSEqC TM 1.2/2.2 compatible level and the 'GoToX' function
Horizontal Rotation	95° (99° max.)
Inclination (motor elevation)	75°
Maximum antenna diameter	120 cm Aluminum or 95 cm Steel
Programmable positions available	50 satellites
Maximum antenna mass gravity point	12 kg (27 lbs), when rotating the dish around the centre-of gravity
Antenna support length	120 mm
Bent motor pole diameter	40 mm ( 1 5/8" )
Rotation speed (unloaded)	2.5°/s (H-18V) 2°/s (V-14V) ±25%
Rotation speed (with a 80-cm dish)	2.3°/s (H-18V) 1.7°/s (V-14V) ±25%
Powered via a coaxial cable	14 / 18 VDC
Power consumption in stand-by mode	15 mA ±25%
Power consumption in operating mode (with a 80-cm dish)	95-150 mA ±25%
Starting movement consumption (80 ms)	350 mA
Operating temperature	-25°C to +70°C
Operating humidity	35% to 100%
Connectors F type	7 mm
Connection	coaxial cable with an impedance of 75 F
Connection cable up to 30 m	inner conductor CU ø 1.02 mm R=22 F/km
Connection cable up to 100m	inner conductor CU ø 1.13 mm R=18 F/km
EAST-WEST limits	hardware fixed, no programmable limit
Fine tuning step	0.36°
Weight with box	2.7 kg (6 lbs)
Maximum permissible wind speed for a 80-cm/120-cm dish	140 km/h/80 km/h (km per hour)
Maximum permissible torque during rotation	15 Nm
Maximum permissible torque on idle	150 Nm
Control buttons	two (west-call and east-store)
Dimensions of packed into box	295 (L) x 132 (W) x 155 (H) mm
Lifetime min.	50,000 cycles over 180° (90°E + 90°W)

This motor will work with the following dishes amongst others:
Fortec Star 80U, 80P dishes
Fortec Star 90U, 90P dishes
Fortec Star 100CM dishes
All Winegard, KTI, Patriot, and Hotdish KU band dishes within the size and weight limits above.

No extra lines needed. HH Motor gets its power and signal from the

same RG6 coaxial cable going to the LNBF.

Tech Support Forums: http://www.sadoun.net/forums/satcontrol/

INSTALLATION
Installation involves setting up your mount to track the satellites along the Clarke belt east to west.
Incorrect alignment usually results in the mount only tracking part of the arc and only a few of the available satellites being received.
HH Motors:
HH motor mount general installation instructions!
See Sample Installation Pictures Here
NOTE: Tighten all the coaxial cable connections only by hand. Using a wrench may over-tighten the connections, causing damage. Such damage is not covered by the Limited warranty.

FAQ:

Do I need a separate power line to connect to the HH Motor?
No. The motor gets its power from the receiver using the same coaxial cable running from the receiver to the LNBF on the dish. You simply disconnect the cable from the LNBF. Connect it to the HH Motor. Then run a short coaxial cable between the motor and the LNBF. You are set.

How do I control the motor to move it East / West?
The motor is controlled by the receiver's remote control. All receivers compliant with the DiSEqC 1.2, 1.3, or USALS protocol have the capability to run an HH motor. Once you initially setup the motor on the satellite arc and store the locations of the satellites, you will be able to move between satellites by simply changing the channel.

Does the motor also adjust for variation in elevation on the dish for each satellite?
Yes it does.

Do I need to skew the LNBF on a motorized dish?
No you don't. Just set the skew at 0 and the motor will tilt the whole dish when it moves.

What is the benefit from motorizing my dish?
Well, by adding a motor to your system you will be able to receive satellite channels from several satellites instead from one only. That way you will gain many more channels economically without investing in many dishes and switches.

Where can I find out what channels are available free to air?

There are many free to air channels available in North America on satellites such as Galaxy 10R, AMC4, Telstar 5, AMC3, etc. There are channels from the USA and from around the world. See http://www.lyngsat.com/america.shtml for a complete listing of what is available. Anything with an F designation is FREE TO AIR.

Channels List

	English
	عربي
	ايران
	Việt-Nam
	European
	สยาม
	한국
	中国版
	Español

Continue SHOPPING

HACKER SAFE certified sites prevent over 99.9% of hacker crime.

Customer Service

::::: Setup Guides, Technical Support, and Instructional Videos ::::: Satisfaction Guaranteed Use of this website are subject to these Terms & Conditions About Us \| Privacy Statement \| Help \| FAQ \| Fax/Mail Order form \| Shipping Information \| Return Policy\| Careers \| Pictures Gallery \| Bookmark page \| Email to a friend \| Free Catalog \| Suppliers Inquiries \| Contact Us
Global Sourcing Solutions & Commerce LLC, DBA Sadoun Satellite Sales 2747 Westbelt Dr, Columbus, OHIO 43228, USA (Map)	Office & Phone Hours: Mon - Fri: 9AM - 5PM Sat: 9AM - 1PM Sunday: Closed
Site © Copyright 1998-2011 Sadoun.com. All rights reserved. Sadoun Satellite Sales is an authorized online retailer of Hughes DIRECTV, Dish Network, and other satellite equipment and systems and is not DIRECTV Inc or Echosphere company. All trademarks and service marks are the property of their respective owners.
Return to top