|
|
 Home > Dishes > Dish Network Dishes > Dish 1000.4
TurboHD
NEW Dish Network
TurboHD DISH 1000.4 Plus
Sadoun Satellite Sales is an AUTHORIZED DISH NETWORK
DEALER IN THE UNITED STATES. The NEW Dish Network TURBO HD DISH
1000.4 is an antenna designed to provide a Single Dish HD solution
to EASTERN or WESTERN US (depending on the model you select from the drop down menu above).
- This dish 1000.4 EA provides signal from satellites 61.5W,
72.7W, and 77W, with the DISH PRO PLUS 1000.4 LNBF.
- This dish 1000.4 WA provides signal from satellites 110W,119W, and 129W, with the DISH PRO PLUS 1000.4 LNBF.
It contains
enhanced peaking controls for an EASIER INSTALLATION and fine-tuning
setup. The Universal Wall/Roof Mount that comes with this dish
purchase, allows you to setup your dish on your roof or exterior
wall of your home.
Installation Support:
INTRODUCTION
- Dish
antenna designed to provide a single-dish HD solution to Eastern US.
-
Watch all local and National HDTV channels offered by
Dish Network.
- Uses DISH
Pro Plus 1000.4 LNBF.
- Includes
enhanced peaking controls for easier installation and fine-tuning of
setup.
FEATURES
- Uses the
same mast and foot as DISH 500+.
- LNBF
Bracket and DPP 1000.4 LNBF include a “keying” feature that ensure only DISH 1000.4 Antenna parts are used together.
- Enhanced
peaking controls provide the ability to perform a rough peak of the dish, and then fine tune the alignment to maximize signal.
- Azimuth
plate and cam provides for fine-tuning of the azimuth angle.
- Elevation rod provides for fine-tuning of the elevation angle, as well as additional stability.
DP PLUS 1000.4 LNBF
- Only
used on the DISH 1000.4.
- Three
receiver output ports support direct connection to either three single-tuner receivers or three DISH Pro Plus (dual-tuner) receivers (when used with a DP Plus Separator) or a combination.
- Includes
an LNB In port to connect a fourth orbital location.
- Default
output ports of the DP Plus 1000.4 EA LNBF are 77°W on Port 1, 72.7°W on Port 2, and 61.5 °W on Port 3.
- Default
output ports of the DP Plus 1000.4 WA LNBF are 129°W on Port 1, 119°W on Port 2, and 110 °W on Port 3
- Compatible with only a DP Plus 44 Switch. When connected to a DPP44 Switch, the LNB IN
port is disabled.
INSTALLATION CONSIDERATIONS
- Only ViP-series
DISH Network receivers that have the circled A
 symbol on their Contents and Features
label should be used with the DISH 1000.4.
- All DISH
1000.4 antenna parts are also marked with the circled A symbol.
- Connect
your peaking meter to PORT
2 on the LNBF, to peak signal. After maximizing the signal received, confirm signal on port 3.
- If your
peaking meter does not output at least 600 mAmps of power, connect a receiver to PORT 1 of the LNBF to power the LNBF while peaking.
- Cables
must be routed on the outside of the mast, as the azimuth plate completely covers the mast opening.
- Nuts and
bolts on the dish that should be tightened with a torque wrench to the torque values indicated in the
Installation Instructions are indicated by a “T” marking, and should be tightened in the following order:
- Mast
Clamp
- Elevation Nuts
- Azimuth
Bolts
- When
tightening the Azimuth bolts, do not tighten the azimuth cam.
Replacement Parts: 157105 Dish 1000.4 Western Arc Replacement LNBF bracket
Special Low Price $10
We are a DISH NETWORK authorized retailer.
|
Continue SHOPPING
|
![[ Super Buddy ]](../../Virtual_Rock/superbuddyspecp_small_small.jpg)
