| |
Heavy Duty Field Replaceable F-connectors that you can swap out with
one 7/16" wrench
|
| |
Durable Rubber Shock-Absorbing case with carabiner clip - longer
lasting than neoprene cases
|
| |
Weather-resistant tough aluminum extrusion enclosure with rubber
gaskets vs. cheap plastic enclosure of competition
|
| |
High Current Limit Level of 600mA that allows it to work with the
Dish Pro Plus and Dish 1000.2
|
| |
Loud audible tone
|
| |
Internal Rechargeable 12 cell NiMH 300 mAh Battery
|
| |
Ability to see battery level remaining
|
| |
Bright LED display, easily viewable in direct sunlight
|
| |
NEW! Heavy-Duty Field
Replaceable F-Connectors (easy change with one 7/16" wrench)
|
| |
22 KHz tone mode to control multiswitches and multi-LNB dishes
|
| |
Bright LED display, easy to read even in direct sunlight
|
| |
Strong audible tone
|
| |
Internal rechargeable NiMH battery
|
| |
Able to power LNB from internal battery or IRD
|
| |
Rugged, compact, weather resistant design
|
| |
Includes DC Cigaretter Lighter Charger, AC Wall Charger
|
| |
Short circuit protection
|
| |
Switches 22KHz On/Off
|
| |
High Current Limit Level of 600mA that allows it to work with the
Dish Pro Plus and Dish 1000.2
|
| |
950-2150 input frequency
|
| |
Tests Coax Cable Runs
|
| |
Selectable Audio On/Off
|
| |
Able to check IRD Set Top Box Receiver Voltage, LNB current amps
|
| |
Works with all LNBs
|
| |
Able to align antenna quickly and reliably without the receiver
|
|
Frequency range
|
950 to 2150 MHz |
|
Impedance
|
75 Ω |
|
Measurable input
level
|
-48 to -8 dBm total
power |
|
|
-60 to -20 dBm per
transponder |
|
Insertion loss
|
14 dB (950 to 1450
MHz) |
|
|
22 dB (1450 to 2150
MHz) |
|
Size (H x W x D)
|
6.5" x 2.7" x 1.1",
1.5 lbs |
|
|
(16.5cm) x (6.9cm) x
(2.8cm), 700g |
|
Temperature range
|
0°F to 125°F |
|
|
(-17°C to +50°C) |
|
Connectors
|
Type F female (field
replaceable) |
|
|
|
Power
|
Uses IRD power when
connected, otherwise uses internal battery. IRD voltage loss through the
SAT Buddy is 1.3 V. Current consumed by the SAT Buddy is 90 mA. |
|
LNB Power
|
Current limited at
600 mA |
|
Internal Battery
Pack
|
Rechargeable 12 cell
NiMH 300 mAh, 12-16 V nominal, automatic shutoff, 1.8 hours typical use
per charge. |
|
Battery Charge Time
|
±10 hours from wall
charger |
|
Wall Charger Output
|
12 VDC, 200 mA,
center pin positive, 2.1mm I.D |
|
|
|
|
Signal Measure Mode
|
|
|
Bargraph LEDs left
row x 10, right row x 1 |
|
|
Dual beep rate with
solid tone at peak |
|
|
|
|
Current/Voltage Mode
|
|
|
0 to 500 mA (each
LED segment is 50 A) |
|
|
10 to 20 volts (each
LED segment is 1V, above 9V) |
![[ Sat Buddy 2 ]](sb2lp.jpg)
